Manual de instrucciones ASUS VH228N

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Follow the screen instructions to complete the update process. ASUS VH228N 4-7 4. 2 BIOS setup program This motherboard supports a programmable Low-Pin Count (LPC) chip that you can update using the provided utility described in section "4. 1 Managing and updating your BIOS. " Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to "Run Setup. " This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you can change the configuration of your computer in the future. For example, you can enable the security password feature or change the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the LPC chip. The LPC chip on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press <Del> during the Power-On Self-Test (POST) to enter the Setup utility; otherwise, POST continues with its test routines. If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. Do this last option only if the first two failed. The Setup program is designed to make it as easy to use as possible. When you set this item to Compatible Mode, Serial ATA and Parallel ATA devices are auto-detected and placed in legacy mode. Configuration options: [Compatible] [Enhanced] The following items appear only if you set the SATA Controller Mode Option item to [Enhanced]. SATA RAID Enable [Disabled] Allows you to enable or disable the Serial ATA RAID function. Configuration options: [Disabled] [Enabled] SATA AHCI Enable [Disabled] Allows you to enable or disable the Serial ATA AHCI function. Configuration options: [Disabled] [Enabled] · · AHCI mode item will support only under Windows environment. Due to the driver limitation, you will not find any SATA driver if you install Fedora core 4. 4-14 Chapter 4: BIOS setup 4. 3. 5 Main IDE Channel 0 Master/Slave; SATA Port 1/2/3/4 PhoenixBIOS Setup Utility IDE Channel 0 Master ItemSpecificHelp Auto = Autotying. ATAPI Removable = ATAPI media (e. g. , LS120, USB Floppy, USB Zip). IDE Removable = IDE removable media (e. g. , IDE Zip drive). User = You supply the hard disk drive type. Type: Multi-Sector Transfers LBA Mode Control 32 Bit I/O Transfer Mode Ultra DMA Mode [Auto] [Disabled] [Disabled] [Disabled] [Standard] [Disabled] F1 ESC Help Exit Select Item Select Menu -/+ Enter Change Values Select Sub-Menu F9 F10 Setup Defaults Save and Exit Type [Auto] Selects the type of IDE drive. Setting to Auto allows automatic selection of the appropriate IDE device type. Select [CD-ROM] if you are specifically configuring a CD-ROM drive. [. . . ] Copy the base driver tar file from the motherboard/system support CD to the directory of your local hard disk. The name format of driver file is "e1000<Version>. tar. gz". For example: the file name of driver version 7. 0. 38 is "e1000-7. 0. 38. tar. gz". The Intel® LAN driver for Linux OS is located in: \Drivers\INTEL 82563EB\PRO1000\LINUX Untar or unzip the archive. [. . . ]