Manual de instrucciones CAME ZC2C

[. . . ] As you create your own sounds by modifying the preset patches, you’ll learn various ways in which the sound can be changed. 5 STEP 2 Create a Sound! Create a Bass Sound 1. Call up the “PRESET B-1” patch. Press the [BANK] button and then press the [2] (B) button Press the [1] button Press the [PRESET PATCH] button 2. Press the [KEY HOLD] button so it’s blinking. 3. Press the second C key from the bottom. You’ll hear an arpeggiated techno bass. 4. Turn the FILTER [RESONANCE] knob to the maximum position. 5. Slowly turn the FILTER [CUTOFF] knob from It’s effective to make this change in sync with the tempo. the maximum position down to the minimum. 6. Set the [RESONANCE] knob at 10 o’clock, and the [CUTOFF] knob at 12 o’clock. 7. In sync with the tempo, raise the LFO [FILTER DEPTH] slider, and then bring it back to the center. For the LFO DEPTH, the center is 0. A NOTE OF ADVICE Use the [CUTOFF] Knob to Fatten the Sound! Moving the [CUTOFF] knob will make the sound fatter or brighter. Once you’ve familiarized yourself with its function, try moving the [CUTOFF] knob between 10 o’clock and one o’clock while you raise and lower the LFO [FILTER DEPTH] slider. [. . . ] This is a synth pad that combines an attack sound with a softer sound. 9. Lower the FILTER [ENV DEPTH] slider downward from the center. The sound of TONE 3 will disappear. For additional expressive possibilities, you can move the FILTER [ENV DEPTH] slider while you play. Turn off the [KEY HOLD] button, and raise the TONE 3 AMP [R] (RELEASE) slider to the maximum position. The time over which the sound of TONE 3 disappears will lengthen. You can change how the sound varies over time by adjusting the ADSR, so you may want to adjust these settings until you get the sound you like. Save the Patch You’ve Created To save your patch, press the [WRITE] button, then select the save-destination patch number, and finally press the [WRITE] button once again. Press the [WRITE] button A NOTE OF ADVICE Adjust the Envelope! For example, if you want to create a gradual attack, such as for strings, try raising the [A] slider. If you want the sound to linger for a while after you take your hand off the keyboard, raise the [R] slider. The sound’s attack and decay are created in the ENV (envelope generator) section. Raise or lower the [A] [D] [S] [R] sliders, and notice how they affect the sound. Volume Symbol A D R Time S R Name Attack time Decay time Sustain level Release time Release the key S Volume change Duration of the attack Duration of the decay Level while sustained Duration of the release Play a key A D 9 STEP 4 Create a Wind Sound 1. Turn the FILTER [CUTOFF] knob all the way to the left. Let’s try playing a wind sound that was created using noise. Noise allows you to produce this type of sound. Set the FILTER ENV [ENV DEPTH] slider to the 60% position. Set the FILTER ENV [S] slider to the 65% position. will be softened. 5 Now you’re ready to create the attack. Set the FILTER ENV [D] slider to the 35% position. The attack 6 To simulate the effect of keeping a finger on the string and sliding to a different fret, press the [MONO] button so it’s lit. 7 Set the [RESONANCE] knob to the 11 o’clock position, giving the sound a distinctive character. 8 Set the AMP ENV [S] slider to the maximum position, and set the [A] [D] [R] sliders to the minimum position. 9 Make fine adjustments to the FILTER ENV [ENV DEPTH] slider to determine the overall tonal character. This synth bass is similar to the sound in chapter 2 “Recall and Edit Presets”, chapter 5 “How to Make a Sound” of the DVD. 12 Synth Lead (PRESET PATCH: H-7) 2 7 3 4 8 11 9 1 5 6 10 1 Press the [CANCEL/SHIFT] button and [WRITE] button to recall the initialized sound. The sawtooth wave is selected. Press the [VARIATION] button to light the [WAVE] button into red. 2 Turn the [PITCH] knob to the right so the sound is raised by an octave. [. . . ] 11 Turn the [CONTROL 1] knob to add reverberation to the lead sound. This synth lead is similar to the sound in chapter 2 “Recall and Edit Presets” of the DVD. 13 APPENDIX Examples of Creating Sounds Synth Pad (PRESET PATCH: H-2) 2 3 6 10 12 1 4 5 7 8 9 11 1 Press the [CANCEL/SHIFT] button and [WRITE] button to recall the initialized sound. The sawtooth wave is selected. button into red. 2 Press the OSC [WAVE] button to select SUPER SAW. [. . . ]