Manual de instrucciones CAME ZE5

[. . . ] Save this manual for future reference. CAUTION TABLE OF CONTENTS WARNING DECAL PLACEMENT . . 14 HOW TO FOLD AND MOVE THE TREADMILL . . Back Cover WARNING DECAL PLACEMENT This drawing shows the locations of the warning decals. If a decal is missing or illegible, call the telephone number on the front cover of this manual and request a free replacement decal. [. . . ] The treadmill will then automatically adjust to the speed and/or incline settings for the next segment. During the workout, the profile will show your progress. Press the Display increase and decrease buttons repeatedly to view the profile. The red line will indicate the current segment of the workout. During a calorie burn workout, the height of the current segment indicates the incline setting for the current segment. During an all-terrain trails workout, the height of the current segment indicates the elevation of the current segment. Each workout is divided into segments. One speed setting and one incline setting are programmed for each segment. Note: The same speed setting and/or incline setting may be programmed for consecutive segments. Press the Start Workout button to start the workout. A moment after you press the button, the walking belt will begin to move. Hold the handrails and begin walking. 20 The workout will continue in this way until the last segment ends. The walking belt will then slow to a stop. A workout summary will then appear on the screen. You can also press the Live Workouts button on the console. To set up an iFit Live account, or for more information about the iFit Live mode, go to www. iFit. com. To switch users, press the Switch User button in the lower right corner of the screen. Then, select the desired user. If you have questions after reading this information, please call Customer Care toll-free at 1-866-608-1798, Mon. –Fri. 8 am–4 pm MT (closed on holidays); visit www. iFit. com/support; or send email to service@iconfitness. com. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] For information about ordering replacement parts, see the back cover of this manual. *These parts are not illustrated. Wheel Console Base Console Module Housing Fan Assembly Handrail Spacer Console Frame Description Key No. 108 109 110 111 112 113 * 1 1 1 2 1 2 – Pulse Bar Top Pulse Ground Wire Pulse Bar Bottom 1/2" Rear Foot Nut Hex Key 3/8" Flat Washer Userʼs Manual Description 35 58 58 37 27 42 40 1 23 38 1 1 46 39 47 1 27 62 35 32 27 38 35 49 26 51 13 50 20 52 9 48 27 42 26 22 EXPLODED DRAWING A 9 1 42 32 43 35 42 45 44 1 42 35 32 21 1 1 42 27 42 35 27 42 58 58 56 1 27 20 28 29 35 32 47 35 1 69 68 35 27 23 36 32 32 1 60 59 31 35 41 25 1 1 46 16 61 59 31 35 66 25 16 1 21 1 1 1 1 60 111 66 Model No. NTL14010. 0 R1210A 112 1 1 111 1 1 11 57 53 11 3 54 55 63 65 1 6 EXPLODED DRAWING B 36 1 Model No. [. . . ]