Manual de instrucciones OMRON A22 DATASHEET

[. . . ] Pushbutton Switch A22 Install in 22-dia. Panel Cutout · Easy mounting and removal of Switch Unit. · Increase wiring efficiency with three-row mounting of Switch Blocks. · Finger protection mechanism on Switch Unit provided as a standard feature. [. . . ] Mushroom Type A22-M 29. 7 dia. 40 dia. 54. 7 (See note 1. ) 54. 7 (See note 1. ) Square/Projection Type A22-C, A22L-C 29. 8 x 29. 8 25. 6 x 25. 6 Square/Full-guard Type A22-D, A22L-D 29. 8 x 29. 8 54. 7 (See note 1. ) 54. 7 (See note 1. ) Note: 1. Alternate operation models are 9. 3 mm longer. Lighted models have the same dimensions as shown above, whether they are with or without Voltage Reduction Units. Pushbutton Switch A22 G-93 Pushbutton Switches Accessories Note: All units are in millimeters unless otherwise indicated. Legend Plate Frames A22Z-332@ A22Z-333@ 28 dia. 28 dia. 0. 1 Lock Ring A22Z-3360 22. 2 dia. 25-dia. 27 dia. 30 dia. Color Cap A22L-30T@ Hole Plug (Round) A22Z-3530 23. 4 dia. 10. 2 30 dia. Sealing Caps For Flat Models A22Z-3600F 32 dia. 26 dia. For Projection Models A22Z-3600T 32 dia. 1r 2r 22. 2 dia. 33 dia. For Full-guard Models A22Z-3600G 31. 5 dia. 22. 2 dia. 32. 5 dia. G-94 Pushbutton Switch A22 Three-throw Spacer A22Z-3003 13. 7 dia. 12. 9 dia. 14. 2 dia. Metallic Bezel Rings For Flat/Projection Models A22Z-3580 28. 7 dia. -0 For Full-guard Models A22Z-3582 28. 7 dia. -0 29. 7±0. 3 dia. Snap-in Legend Plates For Standard Models A22L-3443@-@ For Large Models A22Z-3453@ 29. 7±0. 3 dia. For Emergency-stop Models A22Z-3476-1 (90 dia. ) 90 dia. A22Z-3466-1 (60 dia. ) 60 dia. Black letters Black letters Yellow Yellow 22. 2 dia. 22. 2 dia. Character Film For Round Models A22Z-3460-@ For Square Models A22Z-3480 t0. 22 +0. 1 19. 4-0. 2 dia. t0. 22 21. 5 x 21. 5±0. 2 0. 3 Pushbutton Switch A22 G-95 Pushbutton Switches Lamp Extractor A22Z-3901 30-dia. Metal Flange A22Z-F30 30 dia. 11 dia. 34. 7 dia. Tightening Wrench A22Z-3905 30 dia. 19. 2 dia. Metal Flange A22Z-G30 30 dia. 30 dia. 34. 7 dia. Cap Tightening Tool A22Z-3908 5 dia. 30-dia. Resin Attachment A22Z-A30 34. 7 dia. 22. 2 dia. Cap Puller A3PJ-5080 Lock Plate A22Z-3380 7. 3 dia. Simple Protective Cover A22Z-3700 22. 5 dia. 0. 3 recess 30 × 30 G-96 Pushbutton Switch A22 Control Box (Enclosure) A22Z-B10@ A22Z-B101 (One Hole) A22Z-B101Y Four, 4x38 tapping screws 22. 1+0. 3 dia. -0. 1 Cable Port Hole (Top View) 21 dia. (Lead cable hole) (10x36) 0. 6-mm concave surface Two mounting holes A22Z-B102 (Two Holes) Four, 4x38 tapping screws Two, 22. 1+0. 3 dia. -0. 1 Cable Port Hole (Top View) Pushbutton Switches Two mounting holes 21 dia. (Lead cable hole) (10x36) 0. 6-mm concave surface 16±1 dia. [. . . ] If the Snap-in Legend Plate is transparent, engrave the mirror-written characters on the back of the Snap-in Legend Plate and apply paint coating to the characters. Then apply paint coating of a different color to the remaining part of the Snap-in Legend Plate. Mounting Three-throw Spacer (A22Z-3003) Press and secure the two protruding portions of the Three-throw Spacer to the two indented portions of the inner side of the control panel. Pushbutton Switch A22 G-105 Pushbutton Switches Precautions Common to A22, A22S/W, A22K, M22, and A22E !WARNING Do not apply a voltage between the incandescent lamp and the terminal that is greater than the rated voltage. If the incandescent lamp is broken, the Operation Units may pop out. Always turn OFF the power and wait for 10 minutes before replacing the incandescent lamp. [. . . ]