Manual de instrucciones SAMSUNG DVD-R4000EU INTRODUCTION

[. . . ] q For the best picture quality, if your TV has Component video jacks, you can use component cables instead of the yellow video connector on the Video/Audio cable. Set the Component video out select switch on the back of your DVD recorder to 480p/480i video output mode. If your TV supports progressive scan, select 480p. DVD Recorder TV If you have an AV amplifier Connect either audio cables from the ANALOG AUDIO OUT jacks on the DVD Recorder to the LINE IN jacks on your AV amplifier, or a digital cable from the DIGITAL AUDIO OUT (COAXIAL or OPTICAL) jack on the DVD Recorder to the DIGITAL AUDIO IN jack on your AV amplifier. 2 Step Setup before proceeding Turn on your TV and any other connected equipment OSD Language Setup Press the DVD POWER button. The initial set up OSD language menu will appear. petS Wait!Make sure you complete Step with Step . After all connections are complete, plug the power cord in the wall outlet. [. . . ] Make sure you complete Step with Step . After all connections are complete, plug the power cord in the wall outlet. The word "AUTO" will flicker in the front panel display. It means that the current time is being set automatically (Auto Program) through the antenna under connection and also the channel is being set. When it normally operates, the current time is automatically set and displayed in the front panel display. If "- - - -" appears, however, it means that auto time setting has failed. In that case, set the current time through the manual initial setup. For ease of use, we recommend that you complete the following settings before using the DVD Recorder. Select the desired language using the number buttons. Clock Set With the unit in Stop mode, press the MENU button. Select Setup using the . . . /buttons, then press the or ENTER button. No Disc System Language Audio Video Parental Control Setup Turn on your TV and any other connected equipment OSD(On-Screen Display) Language Setup Clock Set Channel Set Audio Setup MOVE SELECT RETURN EXIT Video Setup Select System using the . . . / buttons, then press the or ENTER button. No Disc Clock Set Channel Set CM Skip Time : 15 Sec System MOVE SELECT RETURN EXIT - Select Clock Set using the . . . / buttons, then press the or ENTER button. No Disc Auto Clock Set Manual Clock Set Clock Set MOVE SELECT RETURN EXIT Select Auto Clock Set using the . . . / buttons, then press the or ENTER button. Select On using the . . . / buttons, then press the or ENTER button. No Disc Auto Clock Set Clock Data CH Time Zone Daylight Saving Auto Clock Set : On Off : Automatic On : Automatic : Automatic - - MOVE SELECT RETURN EXIT The DVD Recorder automatically sets the clock by searching for a channel that carries a time signal and sets your time zone and daylight saving(if applicable). If your clock is set to the wrong time zone or daylight saving, you can adjust these settings without turning off the Auto Clock Set function (see page 24). Then press the or ENTER button. DVD-RAM 4 Step Basic Operation before proceeding DVD-R : Formatting is unnecessary and only Video Mode Recording is supported. Wait!Make sure you complete Step with Step . The following instructions will give you a quick overview about how to use the DVD Recorder. petS Formatting a Disc Recording the current TV program you are watching Making a Timer Recording Finalizing a Disc Press the MENU button with the disc stopped. Press the . . . / buttons to select Disc Manager, and then press the ENTER or button. Press the . . . / buttons to select Disc Format, and then press the ENTER or button. DVD-RAM(VR) Disc Name Disc Protection Disc Format Delete All Title Lists Cartridge Protection Info : : Not protected Disc Manager MOVE SELECT RETURN EXIT DVD-RAM(VR) - q You will be prompted with the confirmation message 'Do you want to format disc?'. Press the oe/ buttons to select Yes, then press the ENTER button. The DVDRAM disc is formatted. DVD-RAM(VR) Disc Name Disc Protection : Disc Manager : Not protected Disc Format Do you want to format disc?Delete All Title Lists Cartridge ProtectNo Inf Yes MOVE SELECT RETURN EXIT - DVD-RW q You will be prompted with the confirmation message 'Choose the recording format for DVD-RW'. Press the oe/ buttons to select the desired format type, then press ENTER. The DVD-RW Disc is formatted. DVD-RW Disc Name Disc Protection : Disc Manager : Not protected Disc Format Choose the recording format for DVD-RW. Delete All Title Lists DVD-VR DVD-V MOVE SELECT RETURN EXIT Formatting a Disc When you insert a blank disc, you will be asked whether or not you want to format or initialize it. [. . . ] The DVD-RW Disc is formatted. DVD-RW Disc Name Disc Protection : Disc Manager : Not protected Disc Format Choose the recording format for DVD-RW. Delete All Title Lists DVD-VR DVD-V MOVE SELECT RETURN EXIT Formatting a Disc When you insert a blank disc, you will be asked whether or not you want to format or initialize it. Since available functions differ depending on the disc type, select a disc that best fits your preferences. DVD-RAM : Must be formatted. Unformatted Disc Do you want to format this disc? [. . . ]