Manual de instrucciones TRENDNET TDM-E400 QUICK INSTALLATION GUIDE

[. . . ] VC/MUX Así como: Para PPPoA (RFC2364) o PPPoE (RFC2516) Nombre de usuario: _______________________ Contraseña: ________________________ Método de autenticación: ¡àPAP o ¡àCHAP Host o dirección IP: _________________ Para conexión IP estática o fija (RFC1483 ó RFC1577) Host: ______________________ Dominio: Gateway: __________________ Dirección IP: _______________________ Máscara de subred: _____________________ IP del servidor DHCP: __________________ IP del servidor de DNS primario: ____________________ IP del servidor de DNS secundario: ____________________ 2 Español 2. Conecte el cable RJ-45 (y/o conecte el cable USB sólo para el modelo USB combinado del TDM-C400). Adjunte el conector de alimentación al enrutador Ethernet ADSL2+. 4. Espere 60 segundos para que el dispositivo se inicie. [. . . ] Haga clic en Commit (Ejecutar). 9 Español 9. El navegador le indicará que sus cambios han sido enviados de manera exitosa. 10. El desplazamiento por defecto del Reboot Mode (Modo reiniciar) es Reboot (Reiniciar) en la subsesión Commit & Reboot (Ejecutar y reiniciar). Haga clic en el botón Reiniciar para reiniciar su módemenrutador ADSL2+. 12. No apague la alimentación ni interrumpa el reinicio de su módem-enrutador ADSL2+. La instalación ha sido completada Para obtener información más detallada sobre la configuración así como de las configuraciones avanzadas del TDM-E400/TDM-C400, por favor consulte la sección de resolución de problemas, el CD-ROM de la Guía del Usuario, o el sitio Web de TRENDnet en http://www. trendnet. com. 10 Español Troubleshooting Q1: POWER LED does not illuminate after the product is turned on. A1: Verify that you are using the power cable provided with the device and that it is securely connected to the ADSL2+ modem and a wall socket/power strip. Q2: I am not sure what type of Internet broadband connection I have for my DSL connection. A2: You can contact your Internet Service Provider's (ISP) Customer Service or Technical Support Department for the correct information. Q3: I specified the IP address 192. 168. 1. 254 in my Web browser, but an error messages says, "The page cannot be displayed. How can I get into the TDM-E400 / TDM-C400 web configuration page?A3: Please check your hardware and TCP/IP settings again by following the instructions in the QIG. Make sure the Power, WAN and the LAN LEDs are on. Then try to access the configuration page using your Web Browser again. Q4: INTERNET LED does not illuminate after phone cable is attached. A4: Verify that a standard telephone cable (called an RJ-11 cable) like the one provided is securely connected to the ADSL port and your wall phone jack. Allow about 30 seconds for the device to negotiate a connection with your ISP. Verify that you are using a straight-through type Ethernet cable to the uplink port on a hub or a cross-over type cable to a stand-alone PC. If you connected the device to an ordinary hub port (not Uplink), you must use a straight-through cable. (To check: hold the connectors at each end of the cable side-by-side with the plastic spring facing down. Looking at the wires from left to right, if the first, second, third, and sixth wires are the same color on the two connectors, then it is a straight-through type. On a cross-over type, wire 1 on one connector should be the same color as wire 3 on the other. The same is true of wires 2 and 6. ) Q5: Ethernet LED does not illuminate after Ethernet cable is attached. [. . . ] Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Check with you Local Authority or Retailer for recycling advice. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. [. . . ]