Manual de instrucciones TRENDNET TEG-S16G QUICK INSTALLATION GUIDE

[. . . ] TEG-MGBSX, TEG-MGBS10, TEG-MGBS40, TEG-MGBS80, TEG-MGBS10D3_5, TEG-MGBS40D3_5) para ranuras Mini-GBIC Aplicación 48-Port Gigabit Web Smart Switch (TEG-S16G) 26-Port Gigabit Web Smart Switch (TEG-224WSplus) 4-Port Gigabit Firewall Router (TWG-BRF114) Multi-Mode Mini GBIC Module (TEG-MGBSX) Internet Cable/DSL Modem Workstation with 10/100Mbps PCI Adapter (TE100-PCIWN) Workstation with 10/100Mbps PCI Adapter (TE100-PCIWN) Gigabit 10/100Mbps 1 Español LC Type Cable Servers with Gigabit PCI Adapters (TEG-PCITXR) Multi-Mode Mini GBIC Module (TEG-MGBSX) 2. Instalación del Hardware Nota: 1. Tras completar la instalación del hardware, utilice el navegador Web para configurar el TEG-S16G. [. . . ] Compruebe que su PC y el TEG-S16G están configurados en el mismo segmento de red. Las ranuras Mini-GBIC están compartidas con los puertos Ethernet Gigabit 45, 46, 47 y 48. Cuando las ranuras Mini-GBIC se estén usando, los puertos Ethernet Gigabit 45, 46, 47 y 48 estarán desactivados. Conecte el Power Cord (Cable de alimentación) en la parte trasera del TEG-S16G y después a la toma corriente. 2. Conecte un cable de red CAT-5e/6 RJ-45 del PC a un puerto Ethernet disponible en el TEG-S16G. 2 Español 3. Herramienta de gestión Web Nota: Si desea encontrar con facilidad todos los conmutadores de gestión Web en la red asigne una dirección IP, cambie la contraseña, actualice la nueva versión del firmware, y después instale la herramienta de gestión para conmutador Web Smart. Siga los siguientes pasos. Para usuarios de Windows 1. Introduzca el CD-ROM del controlador y de la herramienta en la unidad de CD-ROM de su PC y luego haga clic en Install Utility (Instalar herramienta). 2. The default IP address of the TEG-S16G is http://192. 168. 0. 1 and the default password is "admin". Q3: When I access the TEG-S16G using a web browser, I get a screen that tells me "only one user can login". A3: Another computer is configuring the TEG-S16G. If the other user has already logged off and you still get the same screen, then disconnect the power cord from the TEG-S16G, wait for 5 seconds, reconnect the power cord to the TEG-S16G, allow 5 seconds for the Switch to power on, and then attempt to access the web configuration page to login. Q4: I forgot the administration password. A4: Press on the reset button using a pen or paperclip for 10 seconds. If you still encounter problems or have any questions regarding the TEG-S16G, please refer to the User's Guide included on the Utility CD-ROM or contact TRENDnet's Technical Support Department. 6 Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. [. . . ] (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Check with you Local Authority or Retailer for recycling advice. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. [. . . ]